Computerized Testing Machines

Computerized Universal Testing Machine

Our Computerized Universal Testing Machine comes with the below mentioned features.

Technical specifications :- 

  •  Dual Column table top model up to 50kN (Regular model available upto 200 kN) 
  •  Up to four load cells for multiple ranges 
  •  Communicates with standard window based PC 
  •  Batch testing facility for statistical analysis, proof test and cyclic test facility 
  •  Machine is Supplied with AC variable frequency drives 
  •  Speed ranges from 0.5mm/min. to 500mm/min. through servo control motor & drive (optional) 
  •  Sturdy and precise alignment, through precision guides and pre-loaded bearings for higher accuracy (optional).
  • generate various Graphs such as Load v/s Elongation, stress v/s strain, etc.
  • operate with Window PC & printer
  •  testing wide range of materials for Tensile Compression, Bending, Flexural, Shearing, Peeling, Tear & Burst Tests with Elongation measuring device 

Electronic Tensile Testing Machine

Electronic tensile testing machine

Specification:

1. Machine:

Computer controlled equipment to test tensile strength and elongation of a wide range of materials. Compression, Bending,Flexural, Shearing Peeling, Tear & other tests are possible through special grips & fixtures.

2. Force Measurement.

By Electronic Load Cells of high accuracy. Two Load-cells are included, One each for higher and lower strength material.

3. Elongation Measuring Device.

Built-in Device.Measurement through cross - head movement by incremental encoder. For range & resolution,refer specification table.

4. Batch Test Facility.

For a Batch test - can furnish statistical analysis report in regard to minimum, maximum, mean and C.V% of strength and elongation.

5. Cyclic Test Facility.

Particularly Suitable For rubber belting .Automatic loading and unloading of specimen for desired number of cycles.( Maximum 999 cycles) Specimen can be stretched between given load or elongation limit - with 5% tolerance.

6. Proof Test Facility.

Direct indication of proof load at selectable percentage of specimen gauge length.

7. Measuring Unit.

Force Value Display in gm & kgf and print-out in selectable unit - gm, kg, N, cN, kN Or Lbs.

Elongation. Display in mm and printout in mm or Inch.

8. Test Result.

Display. During test all relevant test data including Load - Elongation Curve displayed on Computer screen. Print-out Test Report with Load - Elongation Curve can be had on completion of test .

9. Graph.

Load v/s Elongation & Stress V/S strain graphs. Auto scaling before print out. Special graph against specific need can be provided.

For desired force value , corresponding elongation value & vice-versa can be directly seen on screen.

10. Cross-head Drive & Speeds.

Variable test speed through variable frequency A.C.Drive.

For speed range refer table. Speed selection through computer key board.

Other speeds can be offered, On cost basis against specific requirement

11.Testing Lower Strength Materials.

For testing lower strength material additional load-cell can be provided on cost basis.

12. Protections.

Overload & Over travel protection. Automatic stopping on specimen ruptures.

13. Accuracy.

+ 1% of the verification load OR + 0.2% of rated capacity of range employed, which-ever is greater. Complying IS 1828 ( part 1) : 1991 /ISO 7500 – 1 : 1986

Computerized Universal Testing Machine (UTM)

Our extensive and quality range includes sophisticated Computerized Testing Machines like computerized fabric and Lea tester, that have all the features of microprocessor based version. Further, it has variable speed A.C drive, permanent data storage facility and fine load resolution that 4000 counts for each measuring range.

Some of its other features are as follows:

  • Printout of statistical results that includes minimum, maximum, mean & % CV of load, elongation, count & CSP
  • Speed selection through Computer
  • Custom-built software for specific need etc. with capacity upto 10 KN
  • Count information can be directly received from count balance or through key board
  • Variable speed A.C drive
  • Permanent data storage facility and fine load resolution

Additional Information:
  • Pay Mode Terms: L/C (Letter of Credit)

Computerized Universal Testing Equipment (UTM)

Computerized Universal Testing Equipment (UTM) Specification

1. Machine.
Computer controlled equipment to test tensile strength and elongation of a wide range of materials. Compression, Bending,Flexural, Shearing Peeling, Tear & other tests are possible through special grips & fixtures.

2. Force Measurement.

By Electronic Load Cells of high accuracy. Two Load-cells are included, One each for higher and lower strength material.

3. Elongation Measuring Device.

Built-in Device.Measurement through cross - head movement by incremental encoder. For range & resolution,refer specification table.

4. Batch Test Facility.

For a Batch test - can furnish statistical analysis report in regard to minimum, maximum, mean and C.V% of strength and elongation.

5. Cyclic Test Facility.

Particularly Suitable For rubber belting .Automatic loading and unloading of specimen for desired number of cycles.( Maximum 999 cycles) Specimen can be stretched between given load or elongation limit - with 5% tolerance.

6. Proof Test Facility.

Direct indication of proof load at selectable percentage of specimen gauge length.

7. Measuring Unit.

Force Value Display in gm & kgf and print-out in selectable unit - gm, kg, N, cN, kN Or Lbs.

Elongation. Display in mm and printout in mm or Inch.

8. Test Result.

Display. During test all relevant test data including Load - Elongation Curve displayed on Computer screen. Print-out Test Report with Load - Elongation Curve can be had on completion of test .

9. Graph.

Load v/s Elongation & Stress V/S strain graphs. Auto scaling before print out. Special graph against specific need can be provided.

For desired force value , corresponding elongation value & vice-versa can be directly seen on screen.

10. Cross-head Drive & Speeds.

Variable test speed through variable frequency A.C.Drive.

For speed range refer table. Speed selection through computer key board.

Other speeds can be offered, On cost basis against specific requirement
11.Testing Lower Strength Materials.

For testing lower strength material additional load-cell can be provided on cost basis.

12. Protections.

Overload & Over travel protection. Automatic stopping on specimen ruptures.

13. Accuracy.

+ 1% of the verification load OR + 0.2% of rated capacity of range employed, which-ever is greater. Complying IS 1828 ( part 1) : 1991 /ISO 7500 – 1 : 1986

Computer Control Fabric Tensile Testing Machine

Our extensive and quality range includes sophisticated Computer Control Fabric Tensile Testing Machines like Lea tester, that have all the features of microprocessor based version. Further, it has variable speed A.C drive, permanent data storage facility and fine load resolution that 4000 counts for each measuring range.

Some of its other features are as follows:

  • Printout of statistical results that includes minimum, maximum, mean & % CV of load, elongation, count & CSP
  • Speed selection through Computer
  • Custom-built software for specific need etc. with capacity upto 10 KN
  • Count information can be directly received from count balance or through key board

Computer Tensile Strength Testing Machine

We are leading manufacturer and exporter of high precision range of testing equipment and machinery for all type of materials, over 3 decades with more than 10000 satisfied customer all over the world.

We are able to gain immense expertise in delivering Computerized Tensile Testing Machine to our clients. The offered range of computerized tensile testing machines is made utilizing high grade raw material and innovative technology in complete adherence with the international quality standards. Along with this, the offered range of computerized tensile testing machines is suitably checked on different characteristics to maintain its authenticity throughout the designing procedure.

Features:

  • High tensile strength
  • Durable finish standards
  • Reliable performance

Additional Information:
  • Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)
  • Port of Dispatch: MUMBAI

Computer Tensile Strength Testing Equipment

Computer tensile strength testing Equipment

We are manufacturing and supplying Computer tensile strength testing Equipment that are used for determining tensile strength and elongation of rubber, leather, paper, plywood,metal etc
  • Maximum load 200KN
  • Accurate grade Accuracy Class 1.0/.05
  • Effective measuring range 2% to 100%
  • Measuring accuracy + 1 of load or 0.2% of full scale whichever is
  • higher.
  • Tester resolution 4000 Count in each measuring
  • rage
  • Load sensor Strain gauge type
  • Basic configuration: Data logging of load & extension of control
  • Extended configuration: Data Logging above with extensometer
  • Effective testing width 450mm (width between Colum’s)
  • Effective tensile stroke 600 to 1000mm
  • Range of testing speed 10% to 100%

Electronic Universal Testing Machine

Product Details:
  • Minimum Order Quantity: 1 Piece
  • Brand: KMI
  • Model: 201T

Electronic Universal Testing Machine is used to test your product with pin point accuracy Excellent quality with 2 and more load cell.

1. Machine:

Computer controlled equipment to test tensile strength and elongation of a wide range of materials. Compression, Bending,Flexural, Shearing Peeling, Tear & other tests are possible through special grips & Fixture

2. Force Measurement:

By Electronic Load Cells of high accuracy . Two Load-cells are included, One each for higher and lower strength Material.

3. Test Result:

Display. During test all relevant test data including Load - Elongation Curve displayed on Computer screen. Print-out Test Report with Load - Elongation Curve can be had on completion of test . Number of copies as required can be obtained.

4. Graph.

Load v/s Elongation & Stress V/S strain graphs. Auto scaling before print out. Special graph against specific need can be provided. For desired force value , corresponding elongation value & vice-versa can be directly seen on screen.

5. Repetitive testing work - Separate Files.

For repetitive testing work, separate files can be easily generated by operator and can be used whenever required - for convenience & time saving.

Capacity:100KN


Additional Information:
  • Pay Mode Terms: L/C (Letter of Credit)
  • Packaging Details: Wooden Cases

Computerized Universal Tensile Tester

Computerized Universal Tensile Tester :
  • Max. Capacity - 50KN
  • Test Width (mm) approx. - 100MM               
  • Cross head Travel (mm) approx. -700MM
  • Effective Stroke (mm) approx. -600MM               
  • Cross head Speed (mm/min) – 50 to 500mm/min
  • Cross head Return Speed – 500mm/min
  • Tensile Load Measurement Accuracy - + 1 of load or 0.2% of full scale whichever is higher.
  • Stroke Limiter upper/lower -   Provided
  • Power : 3 HP

 


Additional Information:
  • Item Code: 201T
  • Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)
  • Port of Dispatch: Mumbai
  • Packaging Details: Wooden Box

Computerized Universal Tensile Tester

Computerized Universal Tensile Tester

  • Maximum load 100KN
  • Accurate grade Accuracy Class 1.0/.05
  • Effective measuring range 2% to 100%
  • Measuring accuracy + 1 of load or 0.2% of full scale whichever is higher.
  • Tester resolution 4000 Count in each measuring rage
  • Load sensor Strain gauge type
  • Basic configuration: Data logging of load & extension of control
  • Extended configuration: Data Logging above with extensometer
  • Effective testing width 450mm (width between Colum’s)
  • Effective tensile stroke 600 to 1000mm
  • Range of testing speed 10% to 100%
  • Accuracy of displacement measurement .1% of displacement + .05 mm
Looking for Computerized Testing Machines ?
© Kamal Metal Industries
 
Desktop Site Back to top